Toyota Highlander manuals

Toyota Highlander Service Manual: Strut rod ASSY rear

HINT: COMPONENTS: See page 27-2 .

1. REMOVE REAR WHEEL

2. REMOVE STRUT ROD ASSY REAR

 REMOVE STRUT ROD ASSY REAR


(a) Support the rear axle carrier with a jack.

 REMOVE STRUT ROD ASSY REAR


(b) Remove the bolt and nut, and separate the parking brake cable.

 REMOVE STRUT ROD ASSY REAR


(c) Remove the bolt and nut, and disconnect the strut rod (front side).

NOTICE: When removing the bolt, keep the nut from rotating.

 REMOVE STRUT ROD ASSY REAR


(d) Remove the bolt, nut and strut rod from the rear axle carrier.

NOTICE: When removing the bolt, keep the nut from rotating.

3. TEMPORARILY TIGHTEN STRUT ROD ASSY REAR

 TEMPORARILY TIGHTEN STRUT ROD ASSY REAR


(a) Install the strut rod (rear side), bolt and nut, and temporarily tighten the bolt.

NOTICE: When installing the bolt, fix the nut and temporarily tighten the bolt.

 TEMPORARILY TIGHTEN STRUT ROD ASSY REAR


(b) Support the rear axle carrier.

 TEMPORARILY TIGHTEN STRUT ROD ASSY REAR


(c) Connect the strut rod (front side) with the bolt and nut.

NOTICE: When installing the bolt, fix the nut and temporarily tighten the bolt.

4. STABILIZE SUSPENSION

STABILIZE SUSPENSION


(a) FF: Jack up the rear axle carrier, placing a wood block to avoid damage. Apply load to the suspension so that the installed bolt of the suspension arm assy No.1 (inner side of the vehicle) is horizontally aligned with the center of the rear axle hub.

STABILIZE SUSPENSION


(b) 4WD: Jack up the rear axle carrier, placing a wood block to avoid damage. Apply load to the suspension so that the rear drive shaft assy is horizontally positioned.

5. FULLY TIGHTEN STRUT ROD ASSY REAR

FULLY TIGHTEN STRUT ROD ASSY REAR


(a) Fully tighten the bolt.

Torque: 80 NVm (816 kgfVcm, 59 ftVlbf)

FULLY TIGHTEN STRUT ROD ASSY REAR


(b) Fully tighten the bolt.

Torque: 80 NVm (816 kgfVcm, 59 ftVlbf)

FULLY TIGHTEN STRUT ROD ASSY REAR


(c) Install the parking brake cable with the bolt and nut.

Torque: Bolt: 39 NVm (400 kgfVcm, 29 ftVlbf) Nut: 6.0 NVm (61 kgfVcm, 53 in.Vlbf)

6. INSTALL REAR WHEEL Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)

7. INSPECT REAR WHEEL ALIGNMENT (SEE PAGE 27-5 )

Disposal
1. DISPOSE OF SHOCK ABSORBER ASSY REAR LH (a) Fully extend the shock absorber rod. (b) Using a drill, make a hole in the cylinder somewhere between A and B as shown in the illustration to disch ...

Rear suspension arm ASSY NO.1 LH (FF)
REPLACEMENT HINT: COMPONENTS: See page 27-2 . 1. REMOVE REAR WHEEL 2. REMOVE STABILIZER BAR REAR (SEE PAGE 27-27 ) 3. REMOVE REAR SUSPENSION ARM ASSY NO.1 LH (a) Support the rear axle carrie ...

More about Toyota Highlander:

Parking brake system
PROBLEM SYMPTOMS TABLE Use the table below to help find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part in order. If necessary, replace these parts. Symptom Suspect Area Brake drag Parking bra ...

В© 2011-2019 Copyright www.tohighlander.com