Toyota Highlander manuals

Toyota Highlander Service Manual: Replacement

HINT:

1. REMOVE FRONT WHEEL

2. SEPARATE FRONT STABILIZER LINK ASSY LH

SEPARATE FRONT STABILIZER LINK ASSY LH


(a) Remove the nut and separate the front stabilizer link assy LH from the shock absorber assy front LH.

HINT: If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.

3. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


(a) Loosen the lock nut.

NOTICE:

REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


(b) Remove the bolt and disconnect the front flexible hose No. 1 and speed sensor front LH wire harness.

REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


(c) Remove the 2 nuts and bolts on the lower side of front shock absorber with coil spring.

HINT: When removing the bolts, keep the bolt from rotating and loosen the nut.

REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


(d) Remove the 3 nuts on the upper side of the front shock absorber with coil spring.

(e) Remove the front shock absorber with coil spring.

NOTICE: Make sure that the front speed sensor is disconnected from the front shock absorber.

4. FIX FRONT SHOCK ABSORBER WITH COIL SPRING

FIX FRONT SHOCK ABSORBER WITH COIL SPRING


(a) As shown in the illustration to the left, secure the front shock absorber with coil spring in a vise by clamping onto a double nutted bolt affixed to the bracket at the bottom of the absorber.

5. REMOVE SHOCK ABSORBER ASSY FRONT LH

(a) Using SST, compress the front coil spring LH.

SST 09727-30021 (09727-00010, 09727-00021)

NOTICE: Do not use an impact wrench. It will damage the SST.

HINT: Use 2 of the same type of SST.

(b) Remove the front suspension support sub-assy LH, front suspension support bearing LH, front coil spring seat upper LH, front coil spring insulator upper LH, front coil spring LH, front spring bumper LH and front coil spring insulator lower LH from the shock absorber assy front LH.

6. INSPECT SHOCK ABSORBER ASSY FRONT LH

INSPECT SHOCK ABSORBER ASSY FRONT LH


(a) Compress and extend the shock absorber rod 4 times or more.

Then check that there is no abnormal resistance or sound and operation resistance is normal.

If there is any abnormality, replace the shock absorber assy front LH with a new one.

NOTICE: When disposing of the shock absorber assy front LH, see DISPOSAL on page 26-17 .

7. INSTALL SHOCK ABSORBER ASSY FRONT LH

(a) Install the front coil spring insulator lower LH onto the shock absorber assy front LH.

(b) Install the front spring bumper LH to the piston rod.

INSTALL SHOCK ABSORBER ASSY FRONT LH


(c) Using SST, compress the front coil spring LH.

SST 09727-30021 (09727-00010, 09727-00021)

NOTICE: Do not use an impact wrench. It will damage the SST.

HINT: Use 2 of the same type of SST.

(d) Install the front coil spring LH to the shock absorber assy front LH.

HINT: Fit the lower end of the front coil spring LH in the gap of the spring lnsulator lower LH.

INSTALL SHOCK ABSORBER ASSY FRONT LH


(e) Install the front coil spring insulator upper LH with the mark facing to the outside of the vehicle as shown in the illustration.

INSTALL SHOCK ABSORBER ASSY FRONT LH


(f) Install the front coil spring seat upper LH to the shock absorber assy front LH with the mark facing to the outside of the vehicle.

INSTALL SHOCK ABSORBER ASSY FRONT LH


(g) Install a new front suspension support bearing LH.

INSTALL SHOCK ABSORBER ASSY FRONT LH


(h) Install the front suspension support sub-assy LH with the mark facing to the outside of the vehicle.

(i) Temporarily tighten a new lock nut.

(j) Remove the SST slowly in order to release the coil spring.

SST 09727-30021 (09727-00010, 09727-00021)

8. INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING


(a) Install the front shock absorber with coil spring .

(b) Install the 3 nuts to the upper side of front shock absorber with coil spring.

Torque: 80 NVm (816 kgfVcm, 59 ftVlbf)

NOTICE: Do not tighten the lock nuts until installing the bolts and nuts (lower side).

INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING


(c) Install the 2 bolts and 2 nuts to the lower side of front shock absorber with coil spring.

Torque: 230 NVm (2,350 kgfVcm, 170 ftVlbf)

HINT: When installing the nuts, keep the bolts from rotating and torque the nut.

INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING


(d) Install the front flexible hose No. 1 and speed sensor wire harness front LH with the bolt.

Torque: 19 NVm (194 kgfVcm, 14 ftVlbf)

INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING


(e) Fully tighten the lock nut.

Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)

9. INSTALL FRONT STABILIZER LINK ASSY LH

INSTALL FRONT STABILIZER LINK ASSY LH


(a) Install the front stabilizer link assy LH with the nut.

Torque: 74 NVm (755 kgfVcm, 55 ftVlbf)

HINT: If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.

10. INSTALL FRONT WHEEL Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)

11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (SEE PAGE 26-7 )

Shock absorber ASSY front LH
...

Disposal
HINT: Dispose of the RH side by following the same procedures as with the LH side. 1. DISPOSE OF SHOCK ABSORBER ASSY FRONT LH (a) Fully extend the shock absorber rod. (b) Using a drill, make a ...

More about Toyota Highlander:

Inspection
1. INSPECT FRONT POWER SEAT SWITCH LH (a) Check the resistance between the terminals when each switch is operated. Standard: Slide switch Driver's seat only: Front vertical switch Driver's seat only: Rear vertical switch Reclining switch If the result is not as specifie ...

В© 2011-2024 Copyright www.tohighlander.com