Toyota Highlander manuals

Toyota Highlander Service Manual: Replacement

1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 11-1 )

2. REMOVE FRONT WHEEL

3. REMOVE ENGINE UNDER COVER NO.1

4. REMOVE FRONT FENDER SPLASH SHIELD FRONT RH

5. REMOVE FRONT FENDER SPLASH SHIELD FRONTR LH

6. REMOVE FRONT FENDER APRON SEAL RH

7. DRAIN COOLANT (See page 16-6 )

8. DRAIN AUTOMATIC TRANSAXLE FLUID

(a) Using a 10 mm hexagon wrench, remove the drain plug and gasket. Drain automatic transaxle fluid.

(b) Install a new gasket and the drain plug.

Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)

9. DRAIN TRANSFER OIL (4WD TYPE)

10. REMOVE BATTERY

11. REMOVE AIR CLEANER ASSY

12. DISCONNECT RADIATOR HOSE INLET

13. DISCONNECT RADIATOR HOSE OUTLET

14. DISCONNECT OIL COOLER INLET HOSE

15. DISCONNECT OIL COOLER OUTLET HOSE

16. REMOVE ENGINE MOUNTING STAY NO.2 RH

17. REMOVE ENGINE MOVING CONTROL ROD W/BRACKET

REMOVE ENGINE MOVING CONTROL ROD W/BRACKET


(a) Remove the 3 bolts and engine moving control rod.

18. REMOVE ENGINE MOUNTING BRACKET NO.2 RH

19. REMOVE FAN AND GENERATOR V BELT (See page 14-5 )

20. DISCONNECT VANE PUMP OIL RESERVOIR ASSY

21. DISCONNECT RETURN TUBE SUB-ASSY

DISCONNECT RETURN TUBE SUB-ASSY


(a) Remove the 2 bolts and disconnect the return tube.

22. DISCONNECT UNION TO CHECK VALVE HOSE

23. DISCONNECT TRANSMISSION CONTROL CABLE ASSY (See page 40-34 )

24. DISCONNECT HEATER INLET WATER HOSE

25. DISCONNECT HEATER OUTLET WATER HOSE

26. DISCONNECT FUEL TUBE SUB-ASSY (See page 11-1 )

27. DISCONNECT ENGINE ROOM MAIN WIRE

DISCONNECT ENGINE ROOM MAIN WIRE


(a) Disconnect the engine wire from the ECM and J/B.

(b) Disconnect the engine wire from the engine room J/B.

  1.  Remove the nut fixing the wire harness.
  2.  Using a screwdriver, unlock the engine room J/B.

    Disconnect the engine wire by pulling it upward.

  3.  Disconnect the connectors.
  4.  Remove the body ground.

28. REMOVE EXHAUST PIPE ASSY FRONT (See page 15-2 )

29. REMOVE PROPELLER SHAFT (4WD TYPE)

REMOVE PROPELLER SHAFT (4WD TYPE)


(a) Place the matchmarks on both of the flanges.

(b) Remove the 4 nuts, 4 bolts and 4 washers.

REMOVE PROPELLER SHAFT (4WD TYPE)


(c) Insert SST after removing the propeller shaft.

SST 09325-20010

30. REMOVE FRONT STABILIZER LINK ASSY LH

(a) Using a 6 mm socket hexagon wrench, fix the stud bolt.

(b) Remove the nut and disconnect the stabilizer link.

31. REMOVE FRONT STABILIZER LINK ASSY RH

HINT: Use the same procedures described for the LH side.

32. REMOVE FRONT AXLE HUB RH NUT

REMOVE FRONT AXLE HUB RH NUT


(a) Using SST and a hammer, strike the lock nut covering to remove it.

SST 09930-00010

NOTICE:

(b) Using a 30 mm socket wrench, remove the lock nut.

33. REMOVE FRONT AXLE HUB LH NUT

HINT: Use the same procedures described for the LH side.

34. DISCONNECT SPEED SENSOR FRONT LH

(a) Remove the bolt and disconnect the speed sensor from the steering knuckle.

NOTICE: Keep the speed sensor tip and connection free from a foreign matter.

35. DISCONNECT SPEED SENSOR FRONT RH

HINT: Use the same procedures described for the LH side.

36. DISCONNECT TIE ROD ASSY LH

DISCONNECT TIE ROD ASSY LH


(a) Remove the cotter pin and castle nut.

(b) Using SST, disconnect the tie rod end from the steering knuckle.

SST 09628-6201 1

NOTICE: Be careful not to damage the cover of the ball joint.

37. DISCONNECT TIE ROD ASSY RH

HINT: Use the same procedures described for the LH side.

38. DISCONNECT FRONT SUSPENSION ARM SUB-ASSY LOWER NO.1 LH

DISCONNECT FRONT SUSPENSION ARM SUB-ASSY LOWER NO.1 LH


(a) Fix the crankshaft and remove the 6 setting bolts.

39. DISCONNECT FRONT SUSPENSION ARM SUB-ASSY LOWER NO.1 RH

HINT: Use the same procedures described for the LH side.

40. REMOVE DRIVE PLATE & TORQUE CONVERTER CLUTCH SETTING BOLT

REMOVE DRIVE PLATE & TORQUE CONVERTER CLUTCH SETTING BOLT


(a) Fix the crankshaft and remove the 6 setting bolts.

41. DISCONNECT STEERING INTERMEDIATE SHAFT SUB-ASSY

DISCONNECT STEERING INTERMEDIATE SHAFT SUB-ASSY


(a) Loosen the sliding yoke bolt.

DISCONNECT STEERING INTERMEDIATE SHAFT SUB-ASSY


(b) Place matchmarks on the intermediate shaft and control valve shaft.

(c) Remove the bolt and the steering intermediate shaft.

(d) To prevent the steering wheel from rotating, fix the wheel with the seat belt.

DISCONNECT STEERING INTERMEDIATE SHAFT SUB-ASSY


NOTICE: If the steering wheel is not fixed, the spiral cable will be damaged.

42. DISCONNECT COMPRESSOR AND MAGNETIC CLUTCH

HINT: Hung up the hoses instead of detaching.

43. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

 REMOVE ENGINE ASSEMBLY WITH TRANSAXLE


(a) Set the engine lifter.

(b) Remove the 6 bolts and frame side rail plate RH and LH.

 REMOVE ENGINE ASSEMBLY WITH TRANSAXLE


(c) Remove the 6 bolts and front suspension member brace rear RH and LH.

(d) Carefully remove the engine assembly from the vehicle.

 REMOVE ENGINE ASSEMBLY WITH TRANSAXLE


(e) Install the 2 engine hangers as shown in the illustration.

Parts No.:

 REMOVE ENGINE ASSEMBLY WITH TRANSAXLE


Torque: 38 NVm (387 kgfVcm, 28 ft lbf)

(f) Using a chain block and an engine sling device, hang the engine assembly.

44. REMOVE VANE PUMP ASSY

REMOVE VANE PUMP ASSY


(a) Disconnect the PS oil pressure switch connector.

> (b) Remove the 2 bolts and vane pump from the engine.

45. REMOVE STABILIZER BAR FRONT (4WD TYPE)

46. REMOVE RACK & PINION POWER STEERING GEAR ASSY (4WD TYPE)

47. REMOVE FRONT FRAME ASSY

REMOVE FRONT FRAME ASSY


(a) Remove the nut installing the engine mounting insulator LH.

REMOVE FRONT FRAME ASSY


(b) Remove the nut installing the engine mounting insulator RH.

REMOVE FRONT FRAME ASSY


(c) Remove the nut installing the engine mounting insulator FR.

48. REMOVE FRONT DRIVE SHAFT ASSY RH (4WD TYPE) (See page 30-21 )

49. REMOVE ENGINE MOUNTING BRACKET RR (4WD TYPE)

REMOVE ENGINE MOUNTING BRACKET RR (4WD TYPE)


(a) Remove the 6 bolts and engine mounting bracket RR.

50. REMOVE TRANSFER ASSY (4WD TYPE) (See page 31-9 )

51. REMOVE FRONT DRIVE SHAFT ASSY LH (See page 30-21 )

52. REMOVE FRONT DRIVE SHAFT ASSY RH (2WD TYPE) (See page 30-21 )

53. REMOVE STARTER ASSY (See page 19-4 )

54. REMOVE AUTOMATIC TRANSAXLE ASSY (See page 40-12 )

55. REMOVE DRIVE PLATE & RING GEAR SUB-ASSY

REMOVE DRIVE PLATE & RING GEAR SUB-ASSY


(a) Using SST, fix the crankshaft.

SST 09213-54015 (91651-60855), 09330-00021

REMOVE DRIVE PLATE & RING GEAR SUB-ASSY


(b) Remove the 8 bolts, rear spacer, drive plate and front spacer.

56. INSTALL ENGINE STAND

57. REMOVE ENGINE COVER SUB-ASSY NO.1

58. REMOVE INTAKE MANIFOLD

REMOVE INTAKE MANIFOLD


(a) Remove the 5 bolts, 2 nuts, intake manifold and gasket.

59. INSPECT INTAKE MANIFOLD

INSPECT INTAKE MANIFOLD


(a) Using a precision straight edge and feeler gauge, measure the surface contacting the cylinder head for warpage.

Maximum warpage: 2.0 mm (0.079 in.)

If the warpage is greater than the maximum, replace the manifold.

60. REMOVE VENTILATION HOSE No.1

61. REMOVE VENTILATION HOSE NO.2

62. REMOVE ENGINE WIRE

63. REMOVE INTAKE MANIFOLD INSULATOR NO.1

64. REMOVE GENERATOR ASSY

65. REMOVE OIL LEVEL GAGE SUB-ASSY

66. REMOVE OIL LEVEL GAGE GUIDE

67. REMOVE MANIFOLD CONVERTER INSULATOR NO.1

68. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSY

REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSY


(a) Remove the 3 bolts, 2 nuts, and the No. 1 and No. 2 exhaust manifold stays.

REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSY


(b) Remove the 5 nuts, exhaust manifold converter and gasket.

69. INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSY

INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSY


(a) Using a precision straight edge and feeler gauge, measure the surface contacting the cylinder head for warpage.

Maximum warpage: 0.70 mm (0.0276 in.)

If the warpage is greater than the maximum, replace the manifold.

70. REMOVE WATER INLET

71. REMOVE THERMOSTAT

72. REMOVE IGNITION COIL ASSY

73. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSY

74. REMOVE V-RIBBED BELT TENSIONER ASSY

REMOVE V-RIBBED BELT TENSIONER ASSY


(a) Remove the bolt, nut and belt tensioner.

75. REMOVE DRIVE SHAFT BEARING BRACKET (2WD TYPE)

76. REMOVE ENGINE MOUNTING BRACKET RH

77. REMOVE FUEL DELIVERY PIPE W/INJECTOR (See page 11-10 )

78. REMOVE WATER BY-PASS PIPE NO.1

79. REMOVE OIL COOLER PIPE (W/ OIL COOLER)

80. REMOVE OIL COOLER HOSE (W/ OIL COOLER)

81. REMOVE ENGINE OIL PRESSURE SWITCH ASSY

REMOVE ENGINE OIL PRESSURE SWITCH ASSY


(a) Remove the oil pressure switch.

82. REMOVE KNOCK SENSOR

REMOVE KNOCK SENSOR


(a) Remove the nut and the sensor.

83. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

84. REPLACE PARTIAL ENGINE ASSY

85. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

(a) Install a new gasket to the sensor.

(b) Install the sensor.

Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)

86. INSTALL KNOCK SENSOR

INSTALL KNOCK SENSOR


(a) Install the sensor with the nut.

Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)

HINT: Angling the knock sensor below the horizontal (below 0 ) is recommended.

87. INSTALL ENGINE OIL PRESSURE SWITCH ASSY

(a) Clean the threads of the oil pressure switch. Apply adhesive to 2 or 3 threads of the oil pressure switch.

Adhesive: Part No. 08833-00080 THREE BOND 1344 or equivalent (b) Install the oil pressure switch.

Torque: 15 NVm (153 kgfVcm, 11 ftVlbf)

88. INSTALL OIL COOLER PIPE (W/ OIL COOLER)

(a) Install a new gasket and the oil cooler pipe with the bolt and 2 nuts.

Torque: 9.0 NVm (92 kgfVcm, 80 in.Vlbf)

89. INSTALL WATER BY-PASS PIPE NO.1

(a) Install a new gasket and the by-pass pipe with the bolt and 2 nuts.

Torque: 9.0 NVm (92 kgfVcm, 80 in.Vlbf)

90. INSTALL FUEL DELIVERY PIPE W/INJECTOR (See page 11-10 )

91. INSTALL ENGINE MOUNTING BRACKET RH Torque: 64 NVm (653 kgfVcm, 47 ftVlbf)

92. INSTALL DRIVE SHAFT BEARING BRACKET (2WD TYPE) Torque: 64 NVm (653 kgfVcm, 47 ftVlbf)

93. INSTALL V-RIBBED BELT TENSIONER ASSY

INSTALL V-RIBBED BELT TENSIONER ASSY


(a) Install the belt tensioner with the bolt and nut.

Torque: 60 NVm (612 kgfVcm, 44 ftVlbf)

94. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSY Torque: 9.0 NVm (92 kgfVcm, 80 in.Vlbf)

95. INSTALL IGNITION COIL ASSY Torque: 9.0 NVm (92 kgfVcm, 80 in.Vlbf)

96. INSTALL THERMOSTAT (See page 16-1 1)

97. INSTALL WATER INLET Torque: 9.0 NVm (92 kgfVcm, 80 in.Vlbf)

98. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSY

INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSY


(a) Install a new gasket and the exhaust manifold converter.

Uniformly tighten the 5 nuts in the sequence shown in the illustration.

Torque: 37 NVm (377 kgfVcm, 27 ftVlbf)

INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSY


(b) Install the No. 1 and No. 2 exhaust manifold stays with the 2 bolts and 2 nuts.

Torque: 44 NVm (449 kgfVcm, 32 ftVlbf)

99. INSTALL MANIFOLD CONVERTER INSULATOR NO.1

100. INSTALL OIL LEVEL GAGE GUIDE

(a) Apply a light coat of the engine oil to the O-ring and install it to the guide.

(b) Install the oil level gage and guide with the bolt.

Torque: 9.0 NVm (92 kgfVcm, 80 in.Vlbf)

101. INSTALL GENERATOR ASSY (See page 19-40 )

102. INSTALL INTAKE MANIFOLD

INSTALL INTAKE MANIFOLD


(a) Install a new gasket and the intake manifold with the 5 bolts and 2 nuts. Uniformly tighten the bolts in several passes.

Torque: 30 NVm (306 kgfVcm, 22 ftVlbf)

103. INSTALL DRIVE PLATE & RING GEAR SUB-ASSY

INSTALL DRIVE PLATE & RING GEAR SUB-ASSY


(a) Using SST, fix the crankshaft.

SST 09213-54015 (91651-60855), 09330-00021 (b) Apply adhesive to 2 or 3 threads of the bolt end.

Adhesive: Part No. 08833-00070, THREE BOND or equivalent.

INSTALL DRIVE PLATE & RING GEAR SUB-ASSY


(c) Install the front spacer, drive plate and rear spacer with 8 bolts. Uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque: 98 NVm (1,000 kgfVcm, 72 ftVlbf)

104. INSTALL AUTOMATIC TRANSAXLE ASSY (See page 40-12 )

105. INSTALL STARTER ASSY (See page 19-4 )

Torque: 39 NVm (398 kgfVcm, 29 ftVlbf)

106. INSTALL FRONT DRIVE SHAFT ASSY RH (2WD TYPE) (See page 30-21 )

107. INSTALL FRONT DRIVE SHAFT ASSY LH (See page 30-21 )

108. INSTALL TRANSFER ASSY (4WD TYPE) (See page 31-9 )

109. INSTALL ENGINE MOUNTING BRACKET RR (4WD TYPE)

INSTALL ENGINE MOUNTING BRACKET RR (4WD TYPE)


(a) Install the mounting bracket with the 6 bolts.

Torque: 34 NVm (347 kgfVcm, 25 ftVlbf) for bolt A 64 NVm (653 kgfVcm, 47 ftVlbf) for bolt B

110. INSTALL FRONT DRIVE SHAFT ASSY RH (4WD TYPE) (See page 30-21 )

111. INSTALL FRONT FRAME ASSY

INSTALL FRONT FRAME ASSY


(a) Install the engine mounting insulator LH with the nut.

Torque: 95 NVm (969 kgfVcm, 70 ftVlbf)

INSTALL FRONT FRAME ASSY


(b) Install the engine mounting insulator RH with the nut.

Torque: 95 NVm (969 kgfVcm, 70 ftVlbf)

INSTALL FRONT FRAME ASSY


(c) Install the engine mounting insulator FR with the nut.

Torque: 87 NVm (887 kgfVcm, 64 ftVlbf)

INSTALL FRONT FRAME ASSY


(d) 4WD type: Install the engine mounting insulator RR with 2 nuts.

Torque: 75 NVm (765 kgfVcm, 55 ftVlbf)

112. INSTALL RACK & PINION POWER STEERING GEAR ASSY (4WD TYPE) Torque: 70 NVm (714 kgfVcm, 52 ftVlbf)

113. INSTALL STABILIZER BAR FRONT (4WD TYPE) Torque: 19 NVm (194 kgfVcm, 14 ftVlbf)

114. INSTALL VANE PUMP ASSY

INSTALL VANE PUMP ASSY


(a) Install the vane pump to the engine with the 2 bolts.

(b) Connect the PS oil pressure switch connector.

Torque: 43 NVm (438 kgfVcm, 31 ftVlbf)

115. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

INSTALL ENGINE ASSEMBLY WITH TRANSAXLE


(a) Set the engine assembly with transaxle on the engine lifter.

(b) Install the engine assembly to the vehicle.

(c) Install the frame side plate LH and RH with the 6 bolts.

Torque: 86 NVm (877 kgfVcm, 63 ftVlbf) for bolt A 32 NVm (326 kgfVcm, 24 ftVlbf) for bolt B and nut

INSTALL ENGINE ASSEMBLY WITH TRANSAXLE


(d) Install the front suspension member brace rear RH and LH with the 6 bolts.

Torque: 86 NVm (877 kgfVcm, 63 ftVlbf) for bolt C 32 NVm (326 kgfVcm, 24 ftVlbf) for bolt D and nut

116. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (See page 55-45 )

117. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSY

INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSY


(a) Align the matchmarks on the intermediate shaft and control valve shaft.

Torque: 35 NVm (357 kgfVcm, 26 ftVlbf)

INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSY


(b) Tighten the bolt.

Torque: 35 NVm (357 kgfVcm, 26 ftVlbf)

118. INSTALL BOLT, W/WASHER

INSTALL BOLT, W/WASHER


(a) Fix the crankshaft, and install the 6 setting bolts.

Torque: 41 NVm (418 kgfVcm, 30 ftVlbf)

119. INSTALL FRONT SUSPENSION ARM SUB- ASSY LOWER NO.1 LH

 INSTALL FRONT SUSPENSION ARM SUB- ASSY LOWER NO.1 LH


(a) Install the drive shaft to the steering knuckle.

(b) Install the suspension lower arm with the bolt and the 2 nuts.

Torque: 127 NVm (1,295 kgfVcm, 94 ftVlbf)

120. INSTALL FRONT SUSPENSION ARM SUB-ASSY LOWER NO.1 RH

HINT: Use the same procedures described for the LH side.

121. INSTALL TIE ROD ASSY LH

(a) Connect the tie rod end to the steering knuckle and install a new castle nut.

Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)

NOTICE: Prevent any lubricant from contacting the thread and the taper portions.

After tightening the castle nut, tighten it to the additional direction within 60 to put into a cotter pin.

(b) Insert a new cotter pin.

122. INSTALL TIE ROD ASSY RH

HINT: Use the same procedures described for the LH side.

123. INSTALL SPEED SENSOR FRONT LH Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)

124. INSTALL SPEED SENSOR FRONT RH Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)

125. INSTALL FRONT AXLE HUB LH NUT

 INSTALL FRONT AXLE HUB LH NUT


(a) Using a 30 mm socket wrench, install a new hub nut.

Torque: 294 NVm (3,000 kgfVcm, 217 ftVlbf) (b) Using a chisel and hammer, tapped the front axle hub LH nut.

126. INSTALL FRONT AXLE HUB RH NUT

HINT: Use the same procedures described for the LH side.

127. INSTALL FRONT STABILIZER LINK ASSY LH

(a) Using a 5 mm socket hexagon wrench, fix the stud bolt and install the nut.

Torque: 74 NVm (755 kgfVcm, 55 ftVlbf)

128. INSTALL FRONT STABILIZER LINK ASSY RH

HINT: Use the same procedures described for the LH side.

129. INSTALL PROPELLER SHAFT (4WD TYPE)

INSTALL PROPELLER SHAFT (4WD TYPE)


(a) Align the matchmarks on both the flanges of the front propeller shaft and intermediate shaft, then install and tighten the 4 bolts, 4 washers and 4 nuts.

Torque: 74 NVm (755 kgfVcm, 55 ftVlbf)

130. INSTALL EXHAUST PIPE ASSY FRONT (See page 15-2 )

131. CONNECT FUEL TUBE SUB-ASSY (See page 11-1 )

132. INSTALL RETURN TUBE SUB-ASSY

 INSTALL RETURN TUBE SUB-ASSY


(a) Install the return tube with 2 bolts.

Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)

133. INSTALL FAN AND GENERATOR V BELT (See page 14-5 )

134. INSTALL ENGINE MOUNTING BRACKET NO.2 RH Torque: 52 NVm (530 kgfVcm, 38 ftVlbf)

135. INSTALL ENGINE MOVING CONTROL ROD W/BRACKET

INSTALL ENGINE MOVING CONTROL ROD W/BRACKET


(a) Install the engine mounting control rod with the 3 bolts.

Torque: 64 NVm (653 kgfVcm, 47 ftVlbf) HINT: First, loosely install bolts (1) and (2) with your hand. Then use a wench to install bolt (3). Finally, tighten bolt (2) and (1), in that order.

136. INSTALL ENGINE MOUNTING STAY NO.2 RH Torque: 64 NVm (653 kgfVcm, 47 ftVlbf)

137. INSTALL AIR CLEANER ASSY Torque: 5.0 NVm (51 kgfVcm, 44 in.Vlbf)

138. ADD TRANSFER OIL

(a) Install a new gasket and the filler plug.

Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)

139. ADD AUTOMATIC TRANSAXLE FLUID

140. ADD ENGINE OIL

141. ADD COOLANT (See page 16-6 )

142. CHECK FOR ENGINE OIL LEAKS

143. CHECK FOR ENGINE COOLANT LEAKS (See page 16-6 )

144. INSPECT FOR FUEL LEAKS (See page 11-1 )

145. INSTALL FRONT WHEEL

146. ADJUST FRONT WHEEL ALIGNMENT (See page 26-7 )

147. CHECK IDLE SPEED AND IGNITION TIMING (See page 14-1 )

148. INSPECT CO/HC (See page 14-1 )

149. CHECK ABS SPEED SENSOR SIGNAL (See page 05-765 )

Components
...

Overhaul
1. REMOVE OIL FILTER SUB-ASSY (a) Using SST, remove the oil filter. SST 09228-06501 2. REMOVE OIL FILTER UNION (a) Using a 12 mm hexagon wrench, remove the union. 3. REMOVE OIL FILLER CAP S ...

More about Toyota Highlander:

Rear suspension arm ASSY NO.2 LH (FF)
REPLACEMENT HINT: COMPONENTS: See page 27-2 . 1. REMOVE REAR WHEEL 2. REMOVE REAR SUSPENSION ARM ASSY NO.2 LH (a) Support the rear axle carrier with a jack. (b) Remove the bolt, and disconnect the rear suspension arm assy No.2 (inner side). (c) Remove the bolt, nut and the rear suspe ...

В© 2011-2024 Copyright www.tohighlander.com