Toyota Highlander manuals

Toyota Highlander Service Manual: On-vehicle inspection

1. INSPECT AIR-FUEL RATIO COMPENSATION SYSTEM

INSPECT AIR-FUEL RATIO COMPENSATION SYSTEM


(a) Measure the voltage between the terminals of the ECM connectors.

Standard:

INSPECT AIR-FUEL RATIO COMPENSATION SYSTEM


NOTICE: Connect test leads to the connector's backside. The connectors should not be disconnected from the ECM.

HINT: Voltage between the terminals of the ECM is kept constant regardless of the voltage of the A/F sensor.

(b) Connect the hand-held tester to the DLC3.

(c) Select "DATA MONITOR". Then select "A/FS B1 S1", "A/FS B2 S1" and "O2S B1 S2" to display the monitors.

(d) Warm up the A/F sensor with the engine speed at 2,500 rpm for approximately 2 minutes.

INSPECT AIR-FUEL RATIO COMPENSATION SYSTEM


(e) Keep the engine speed at 2,500 rpm and confirm that the displays of "A/FS B1 S1" and "A/FS B2 S1" are as shown in the illustration.

HINT:

(f) Confirm that the display of "O2S B1 S2" changes between 0 to 1 V with the engine speed at 2,500 rpm.

2. INSPECT FUEL CUT OFF/RESTART RPM

(a) Increase the engine speed to at least 3,500 rpm.

(b) Use a sound scope to check for the injector operating noise.

(c) When the accelerator pedal is released, injector operating noise stops momentarily and then resumes.

Standard:

INSPECT FUEL CUT OFF/RESTART RPM


If the result is not as specified, check for DTCs. If a DTC is present, follow the repair procedures according to the DTC.

3. VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

 VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS


(a) Check for cracks, leaks or damage

HINT: Removal or problems with the engine oil dipstick, oil filler cap, PCV hose and other components may cause the engine to run improperly. Disconnection, looseness or cracks in the parts of the air induction system between the throttle body and cylinder head will allow air suction and cause the engine to run improperly.

Be sure to check the areas indicated by the arrow marks.

If necessary, replace any damage parts.

4. Using hand-held tester: INSPECT EVAP SYSTEM LINE

 Using hand-held tester: INSPECT EVAP SYSTEM LINE


(a) Warm up and stop the engine.

  1.  Warm up the engine to normal operating temperature.

(b) Install a vacuum gauge (EVAP control system test equipment vacuum gauge) to the EVAP service port on the purge line.

 Using hand-held tester: INSPECT EVAP SYSTEM LINE


(c) Connect the hand-held tester to the DLC3.

(d) Start the engine.

(e) Turn the hand-held tester main switch ON.

(f) Use the ACTIVE TEST mode on the hand-held tester to operate the VSV for EVAP.

 Using hand-held tester: INSPECT EVAP SYSTEM LINE


(g) Check the vacuum while the engine is idling.

Standard: Maintain at 0.368 to 19.713 in.Hg (5 to 268 in.Aq) for over 5 seconds.

HINT: If the vacuum does not change, the hose connecting the VSV to the service port has come loose or is blocked, or the VSV is malfunctioning.

(h) Stop the engine.

(i) Disconnect the hand-held tester from the DLC3.

(j) Disconnect the vacuum gauge from the EVAP service port on the purge line.

 Using hand-held tester: INSPECT EVAP SYSTEM LINE


(k) Connect a pressure gauge to the EVAP service port on the purge line.

 Using hand-held tester: INSPECT EVAP SYSTEM LINE


(l) Connect the hand-held tester to the DLC3.

(m) Turn the ignition switch ON.

(n) Turn the hand-held tester main switch ON.

(o) Use the ACTIVE TEST mode on the hand-held tester to operate the VSV for CCV.

NOTICE: In step (m), the ignition switch should be ON, but the engine should not be running.

HINT: If the check is not completed within 10 minutes, the VSV for CCV will be reset and close automatically.

 Using hand-held tester: INSPECT EVAP SYSTEM LINE


(p) Check the pressure.

  1.  Add 13.5 to 15.5 in.Aq of pressure from the EVAP service port.

Standard: 2 minutes after the pressure is added, the gauge should still read over 7.7 to 8.8 in.Aq.

HINT: If you cannot add pressure, the hose connecting the VSV for EVAP canister fuel tank has become disconnected or the VSV is open.

 Using hand-held tester: INSPECT EVAP SYSTEM LINE


  1. Check if the pressure decreases when the fuel tank cap is removed while adding pressure.

HINT: If the pressure does not decrease when the fuel tank cap is removed, the hose connecting the service port to the fuel tank is blocked.

(q) Turn the ignition switch OFF.

(r) Disconnect the hand-held tester from the DLC3.

5. Not using hand-held tester: INSPECT EVAP SYSTEM LINE

Not using hand-held tester: INSPECT EVAP SYSTEM LINE


(a) Warm up and stop the engine.

  1.  Warm up the engine to normal operating temperature.

(b) Install a vacuum gauge (EVAP control system test equipment vacuum gauge) to the EVAP service port on the purge line.

Not using hand-held tester: INSPECT EVAP SYSTEM LINE


(c) Disconnect the VSV connector for EVAP.

(d) Connect the battery's positive (+) and negative (-) leads to the VSV terminals for EVAP.

(e) Start the engine.

Not using hand-held tester: INSPECT EVAP SYSTEM LINE


(f) Check the vacuum while the engine is idling.

Standard: Maintain at 0.368 to 19.713 in.Hg (5 to 268 in.Aq) for over 5 seconds.

HINT: If the vacuum does not change, the hose connecting the VSV to the service port has come loose or is blocked, or the VSV is malfunctioning.

(g) Stop the engine.

(h) Disconnect the battery's positive (+) and negative (-) leads from the VSV terminals for EVAP.

(i) Reconnect the VSV connector for EVAP.

(j) Disconnect the vacuum gauge from the EVAP service port on the purge line.

Not using hand-held tester: INSPECT EVAP SYSTEM LINE


(k) Connect a pressure gauge to the EVAP service port on the purge line.

Not using hand-held tester: INSPECT EVAP SYSTEM LINE


(l) Disconnect the VSV connector for CCV.

(m) Connect the battery's positive (+) and negative (-) leads to the VSV terminals for CCV.

NOTICE: Incorrect electrode connection causes damage to the VSV.

Pay due attention when connecting the lead wire.

Not using hand-held tester: INSPECT EVAP SYSTEM LINE


(n) Check the pressure.

  1.  Add 13.5 to 15.5 in.Aq of pressure from the EVAP service port.

Standard: 2 minutes after the pressure is added, the gauge should still read over 7.7 to 8.8 in.Aq.

HINT: If you cannot add pressure, the hose connecting the VSV for EVAP canister fuel tank has become disconnected or the VSV is open.

Not using hand-held tester: INSPECT EVAP SYSTEM LINE


  1. Check if the pressure decreases when the fuel tank cap is removed while adding pressure.

HINT: If the pressure does not decrease when the fuel tank cap is removed, the hose connecting the service port to the fuel tank is blocked.

(o) Disconnect the battery's positive (+) and negative (-) leads from the VSV terminals for CCV.

(p) Reconnect the VSV connector for CCV.

(q) Disconnect the pressure gauge from the EVAP service port on the purge line.

6. CHECK AIR TIGHTNESS IN FUEL TANK AND FILLER PIPE

CHECK AIR TIGHTNESS IN FUEL TANK AND FILLER PIPE


(a) Disconnect the vent line hose from the fuel tank (see page 12-28 ).

(b) Connect the pressure gauge to the fuel tank.

(c) Apply pressure to the fuel tank to create an internal pressure of 4 kPa (41 gf/cm2, 0.58 psi).

(d) Check that the internal pressure of the fuel tank is maintained for 1 minute.

v (e) Check the connected portions of each hose and pipe.

(f) Check the installed parts on the fuel tank.

If malfunctions, damage or other problems are found, replace the fuel tank and filler pipe.

(g) Reconnect the vent line hose to the fuel tank.

7. INSPECT FUEL CUTOFF VALVE AND FILL CHECK VALVE

INSPECT FUEL CUTOFF VALVE AND FILL CHECK VALVE


(a) Disconnect the vent line hose from the fuel tank (see page 12-28 ).

(b) Connect the pressure gauge to the fuel tank.

(c) Fill the fuel tank with fuel.

(d) Apply pressure of 4 kPa (41 gf/cm2, 0.58 psi) to the vent port of the fuel tank.

HINT: It is necessary to check the amount of fuel in the fuel tank. When the fuel tank is full, the float valve of the fill check valve is closed and no air can pass through.

(e) Remove the fuel tank cap, and check that pressure drops.

If pressure does not drop, replace the fuel tank assembly.

(f) Reconnect the vent line hose to the fuel tank.

8. CHECK AIR INLET LINE

CHECK AIR INLET LINE


(a) Disconnect the air inlet line hose from the charcoal canister.

(b) Check that air can flow freely into the air inlet line.

If air cannot flow freely into the air inlet line, repair or replace it.

(c) Reconnect the air inlet line hose to the charcoal canister.

9. INSPECT VAPOR PRESSURE SENSOR

INSPECT VAPOR PRESSURE SENSOR


(a) Measure the power source voltage of the ECM connectors.

Standard

INSPECT VAPOR PRESSURE SENSOR


If the voltage is not as specified, replace the ECM.

(b) Measure the power output of the ECM connectors.

  1.  Remove the fuel tank cap.

Standard

INSPECT VAPOR PRESSURE SENSOR


If the voltage is not as specified, replace the ECM.

  1.  Reinstall the fuel tank cap.
Location
SYSTEM DIAGRAM The emission control system is determined by the ECM based on signals from various sensors. ...

Inspection
1. INSPECT VENTILATION VALVE SUB-ASSY (a) Install a clean hose to the ventilation valve. (b) Check ventilation valve operation.  Blow air into the cylinder head side, and check that a ...

More about Toyota Highlander:

Pictorial index
Exterior Doors Locking/unlocking Opening/closing the side windows Locking/unlocking by using the mechanical key* Warning lights/warning messages Back door Locking/unlocking Warning lights/warning messages Glass hatch Warning lights/warning messages ...

В© 2011-2024 Copyright www.tohighlander.com