1. HEADLAMP DIMMER SWITCH ASSY
(a) Inspect light control switch.
Standard:
(b) Inspect headlamp dimmer switch.
Standard:
(c) Inspect turn signal switch.
Standard:
(d) w/ Front Fog Lamp: Inspect front fog light switch.
Standard:
2. HAZARD WARNING SWITCH ASSY
(a) w/o navigation system: Measure the resistance according to the value(s) in the table below.
Standard:
(b) w/ navigation system: Measure the resistance according to the value(s) in the table below.
Standard:
3. FRONT DOOR COURTESY LAMP SWITCH ASSY
(a) Measure the resistance according to the value(s) in the table below.
Standard:
4. REAR DOOR COURTESY LAMP SWITCH ASSY
(a) Measure the resistance according to the value(s) in the table below.
Standard:
5. BACK DOOR LOCK ASSY
(a) Inspect back door courtesy lamp switch assy.
Standard:
6. ROOM LAMP ASSY NO.1
(a) Measure the resistance according to the value(s) in the table below.
Standard:
b) Connect the positive (+) lead from the battery to the terminal 1 and negative (-) lead to the terminal 2, then check that the lamp comes on when the switch is in the DOOR position.
(c) Connect the positive (+) lead from the battery to the terminal 1 and negative (-) lead to the terminal 3, then check that the lamp comes on when the switch is in the ON position.
7. ROOM LAMP ASSY NO.2
(a) Measure the resistance according to the value(s) in the table below.
Standard:
b) Connect the positive (+) lead from the battery to the terminal 1 and negative (-) lead to the terminal 2, then check that the lamp comes on when the switch is in the DOOR position.
(c) Connect the positive (+) lead from the battery to the terminal 1 and negative (-) lead to the terminal 3, then check that the lamp comes on when the switch is in the ON position.
8. MAP LAMP ASSY
(a) Inspect the map lamp in the overhead J/B.
9. COURTESY LAMP ASSY
(a) Connect the positive (+) lead from the battery to terminal 1 and negative (-) lead to terminal 2, then check that the lamp comes on.
10. LH VISOR ASSY
(a) Connect the positive (+) lead from the battery to one of the terminals and the negative (-) lead to other terminal, then check that the lamp comes on when the switch is in the ON position.
11. RH VISOR ASSY
(a) Connect the positive (+) lead from the battery to one of the terminals and the negative (-) lead to other terminal, then check that the lamp comes on when the switch is in the ON position.
12. GLOVE BOX LAMP ASSY
(a) Connect the positive (+) lead from the battery to one of the terminals and the negative (-) lead to other terminal, then check that the lamp comes on when the switch is in the ON position.
13. KEY CYLINDER LAMP
(a) w/ Theft deterrent system: Connect the positive (+) lead from the battery to terminal 2 and negative (-) lead to terminal 6, then check that the lamp comes on.
(b) w/o Theft deterrent system: Connect the positive (+) lead from the battery to terminal 2 and negative (-) lead to terminal 1, then check that the lamp comes on.
14. HEADLAMP RELAY
(a) Measure the resistance according to the value(s) in the table below.
Standard:
15. TAIL LAMP RELAY
(a) Measure the resistance according to the value(s) in the table below.
Standard:
16. FOG LAMP RELAY
(a) Measure the resistance according to the value(s) in the table below.
Standard:
17. DRL NO.2 RELAY
(a) Measure the resistance according to the value(s) in the table below.
Standard:
18. DRL NO.3 RELAY
(a) Measure the resistance according to the value(s) in the table below.
Standard:
19. DRL NO.4 RELAY
(a) Measure the resistance according to the value(s) in the table below.
Standard:
20. STOP LAMP SWITCH ASSY
(a) Measure the resistance according to the value(s) in the table below.
Standard:
Setting the vehicle speed (vehicle-to-vehicle distance control
mode)
Press the “on-off” button to
activate the cruise control.
Radar cruise control indicator will
be displayed.
Press the button again to deactivate
the cruise control.
Accelerate or decelerate the
vehicle to the desired speed,
and push the lever down to set
the speed.
...