Toyota Highlander manuals

Toyota Highlander Service Manual: Charging system (2AZ-FE)

PRECAUTION

CAUTION:

ON-VEHICLE INSPECTION

1. CHECK BATTERY ELECTROLYTE LEVEL

(a) Check the electrolyte quantity of each cell.

Maintenance-free battery: If it is under the lower level, replace the battery.

Except Maintenance-free battery: If it is under the lower level, add distilled water.

2. Except Maintenance-free battery: CHECK BATTERY SPECIFIC GRAVITY

(a) Check the specific gravity of each cell.

Standard specific gravity: 1.25 to 1.29 at 20C (68F)

If the specific gravity is less than the specification, charge the battery.

3. Maintenance-free battery: CHECK BATTERY VOLTAGE

(a) After the vehicle has run for 20 minutes, stop the engine.

(b) Turn the ignition switch ON, and operate the headlight, blower fan and defogger for 1 minute.

(c) Turn the ignition switch OFF.

(d) Measure the battery voltage.

Standard voltage: 12.5 to 12.9 V at 20C (68F)

If the voltage is less than specification, charge the battery.

4. CHECK BATTERY TERMINALS, FUSIBLE LINK AND FUSES

(a) Check that the battery terminals are not loose or corroded.

If the terminals are corroded, clean the terminals.

(b) Check the fusible link and fuses for resistance of below 1 W.

5. INSPECT DRIVE BELT

INSPECT DRIVE BELT


(a) Check the belt for wear, cracks and other signs of damage.

If any defect is found, replace the drive belt.

HINT:

Replace the drive belt if the following defects are found:

INSPECT DRIVE BELT


(b) Check that the belt fits properly in the ribbed grooves.

HINT: With your hand, confirm that the belt has not slipped out of the groove on the bottom of the pulley.

6. VISUALLY CHECK GENERATOR WIRING

(a) Check that the wiring is in good condition.

7. LISTEN FOR ABNORMAL NOISES FROM GENERATOR

(a) Check that there is no abnormal noise from the generator while the engine is running.

8. INSPECT CHARGE WARNING LAMP CIRCUIT

(a) Turn the ignition switch ON. Check that the charge warning lamp turns on.

(b) Start the engine and check that the lamp turns off.

If the lamp does not operate as specified, troubleshoot the charge warning lamp circuit.

9. INSPECT CHARGING CIRCUIT WITHOUT LOAD

INSPECT CHARGING CIRCUIT WITHOUT LOAD


HINT: If a battery/generator tester is available, connect the tester to the charging circuit according to the manufacturer's instructions.

(a) If a tester is not available, connect an ammeter and voltmeter to the charging circuit as follows.

  1.  Disconnect the wire from terminal B of the generator and connect it to the negative (-) lead of the ammeter.
  2.  Connect the ammeter's positive (+) lead to terminal B of the generator.
  3.  Connect the voltmeter's positive (+) lead to terminal B of the generator.
  4.  Ground the voltmeter's negative (-) lead.

(b) Check the charging circuit.

  1.  Keep the engine speed at 2,000 rpm, check the reading on the ammeter and voltmeter.

Standard amperage: 10 A or less Standard voltage: 13.2 to 14.8 V

If the result is not as specified, replace the generator.

10. INSPECT CHARGING CIRCUIT WITH LOAD

(a) With the engine running at 2,000 rpm, turn on the high-beam headlamps and turn the heater blower switch to the HI position.

(b) Check the reading on the ammeter.

Standard amperage: 30 A or more

HINT:

Overhaul
1. REMOVE MAGNETIC SWITCH ASSY (a) Remove the nut and disconnect the lead wire from the magnetic switch. (b) Remove the 2 screws holding the magnetic switch to the starter drive housing. (c ...

Generator ASSY (2AZ-FE)
...

More about Toyota Highlander:

Supplemental restraint system
TORQUE SPECIFICATION SEAT BELT TORQUE SPECIFICATION WIPER & WASHER TORQUE SPECIFICATION INSTRUMENT PANEL/METER TORQUE SPECIFICATION ...

В© 2011-2024 Copyright www.tohighlander.com