Toyota Highlander manuals

Toyota Highlander Service Manual: Transfer case oil seal (4WD)

Toyota Highlander Service Manual / Transfer / Transfer case oil seal (4WD)

REPLACEMENT

1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (3MZ-FE ENGINE TYPE) (SEE PAGE 14-149 )

2. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (2AZ-FE ENGINE TYPE) (SEE PAGE 14-24 )

3. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET (2AZ-FE ENGINE TYPE) (SEE PAGE 31-9 )

4. REMOVE TRANSFER STIFFENER PLATE RH (2AZ-FE ENGINE TYPE) (SEE PAGE 31-9 )

5. REMOVE AUTOMATIC TRANSMISSION W/TRANSFER (3MZ-FE ENGINE TYPE) (SEE PAGE 40-20 )

6. REMOVE TRANSFER ASSY (SEE PAGE 31-9 )

7. REMOVE CTR DIFFERENTIAL LOCK SLEEVE (SEE PAGE 31-9 )

SST 09308-00010

8. REMOVE TRANSFER CASE OIL SEAL

REMOVE TRANSFER CASE OIL SEAL


(a) Using SST, remove the oil seal from the case.

SST 09308-00010

NOTICE: Do not damage the oil-seal-fitted surface of the case.

9. INSTALL TRANSFER CASE OIL SEAL

INSTALL TRANSFER CASE OIL SEAL


(a) Using SST, drive a new oil seal into the case to the position shown in the illustration.

SST 09387-00010, 09950-70010 (09951-07150)

NOTICE: Do not install it obliquely.

(b) Apply small amount of MP grease to the oil seal lip.

10. INSTALL CTR DIFFERENTIAL LOCK SLEEVE (SEE PAGE 31-9 )

SST 09950-60010 (09951-00610), 09950-70010 (09951-07150)

11. INSTALL TRANSFER ASSY (SEE PAGE 31-9 )

12. INSTALL TRANSFER STIFFENER PLATE RH (2AZ-FE ENGINE TYPE) (SEE PAGE 31-9 )

13. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET (2AZ-FE ENGINE TYPE) (SEE PAGE 31-9 )

14. INSTALL AUTOMATIC TRANSMISSION W/TRANSFER (3MZ-FE ENGINE TYPE) (SEE PAGE 40-20 )

15. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (3MZ-FE ENGINE TYPE) (SEE PAGE 14-149 )

16. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (2AZ-FE ENGINE TYPE) (SEE PAGE 14-24 )

Transfer RH bearing retainer oil seal (4WD)
REPLACEMENT 1. REMOVE EXHAUST PIPE ASSY FRONT (3MZ-FE ENGINE TYPE) (SEE PAGE 15-5 ) 2. REMOVE EXHAUST PIPE ASSY FRONT (2AZ-FE ENGINE TYPE) (SEE PAGE 15-2 ) 3. DRAIN AUTOMATIC TRANSAXLE FLUID (a) R ...

Transfer extension housing type T oil seal (4WD)
REPLACEMENT 1. REMOVE EXHAUST PIPE ASSY (3MZ-FE ENGINE TYPE) (SEE PAGE 15-5 ) 2. REMOVE EXHAUST PIPE ASSY (2AZ-FE ENGINE TYPE) (SEE PAGE 15-2 ) 3. REMOVE TRANSFER CASE NO.1 PLUG 4. REMOVE TRANSFER ...

More about Toyota Highlander:

Lubrication system (3MZ-FE)
ON-VEHICLE INSPECTION 1. CHECK ENGINE OIL LEVEL (a) Warm up the engine, stop the engine and wait for 5 minutes. The oil level should be between the dipstick's low level mark and full level mark. If the oil level is low, check for leakage and add oil up to the full level mark. NOTICE: Do ...

В© 2011-2022 Copyright www.tohighlander.com