Toyota Highlander manuals

Toyota Highlander Service Manual: Rear suspension arm ASSY NO.2 LH (4WD)

Toyota Highlander Service Manual / Rear suspension / Rear suspension arm ASSY NO.2 LH (4WD)

REPLACEMENT

HINT: COMPONENTS: See page 27-2 .

1. REMOVE REAR WHEEL

2. REMOVE REAR SUSPENSION ARM ASSY NO.2 LH

REMOVE REAR SUSPENSION ARM ASSY NO.2 LH


(a) Support the rear axle carrier with a jack.

(b) Place matchmarks on the adjust cams and rear suspension member sub-assy.

(c) Remove the nut, camber adjust cam and toe adjust cam, and disconnect the rear suspension arm assy No.2 (inner side).

NOTICE: When removing the nut, keep the bolt from rotating.

REMOVE REAR SUSPENSION ARM ASSY NO.2 LH


(d) Remove the bolt, nut and the rear suspension arm assy No.2 (outer side) from the rear axle carrier.

NOTICE: When removing the bolt, keep the nut from rotating.

3. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 LH

TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 LH


(a) Install the rear suspension arm No.2 (inner side) to the rear suspension member sub-assy with the camber adjust cam and toe adjust cam, and temporarily tighten the nut.

TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 LH


HINT: Ensure that the paint mark on the rear suspension arm assy No.2 faces to the rear side of the vehicle.

TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 LH


(b) Connect the rear suspension arm assy No.2 (outer side) to the rear axle carrier with the bolt and nut.

NOTICE: When installing the bolt, fix the nut and temporarily tighten the bolt.

4. STABILIZE SUSPENSION (SEE PAGE 27-13 )

5. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 LH

FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 LH


(a) Align the matchmarks on the adjust cams and rear suspension member sub-assy.

(b) Fully tighten the nut.

Torque: 100 NVm (1,020 kgfVcm, 74 ftVlbf)

FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 LH


(c) Fully tighten the bolt.

Torque: 112 NVm (1,140 kgfVcm, 83 ftVlbf)

6. INSTALL REAR WHEEL Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)

7. INSPECT REAR WHEEL ALIGNMENT (SEE PAGE 27-5 )

Rear suspension arm ASSY NO.2 LH (FF)
REPLACEMENT HINT: COMPONENTS: See page 27-2 . 1. REMOVE REAR WHEEL 2. REMOVE REAR SUSPENSION ARM ASSY NO.2 LH (a) Support the rear axle carrier with a jack. (b) Remove the bolt, and disconne ...

Stabilizer bar rear (FF)
REPLACEMENT HINT: COMPONENTS: See page 27-2 . 1. REMOVE REAR WHEEL 2. REMOVE REAR STABILIZER LINK ASSY LH (a) Remove the 2 nuts and stabilizer link. HINT: If the ball joint turns together w ...

More about Toyota Highlander:

Locking and unlocking the doors and key linked functions
Use the mechanical key In order to perform the following operations: locks all the doors closes the windows and moon roof*1 (turn and hold)*2   Unlocks the door turning the key rearward unlocks the driver¢¦s door. Turning the key once again within 5 seconds unlocks the ot ...

В© 2011-2019 Copyright www.tohighlander.com